Underdrive Pulley - Duratec - Focaljet

**afraziaaaa** · 08-31-2007, 04:18 PM

Can anyone tell me where the larger pulley is supposed to go? (Not the one for the crankshaft.)

**cfmfocus2** · 08-31-2007, 04:22 PM

The water pump.

**afraziaaaa** · 08-31-2007, 04:22 PM

Also, what is the "supplied M6 bolt" referred to in step 7 in the following thread:

http://forums.focaljet.com/5581148-post9.html

???

**afraziaaaa** · 08-31-2007, 04:28 PM

One more question and that's it, I promise!!! (At least until I think of another one

)

What is the "supplied plate" in step 8 of the directions linked in the above post?

"Using the supplied plate, hold the crankshaft pulley in place while removing the crankshaft pulley bolt"

**afraziaaaa** · 09-04-2007, 12:52 PM

Ok...one more. Does the larger water pump pulley that comes with the kit drive the water pump at normal speed, or is that pulley only used to retain the factory size belt?

**only_in_a_domestic** · 09-04-2007, 03:24 PM

both im pretty sure

**cfmfocus2** · 09-04-2007, 03:46 PM

Quote:

Originally Posted by afraziaaaa

Ok...one more. Does the larger water pump pulley that comes with the kit drive the water pump at normal speed, or is that pulley only used to retain the factory size belt?

The water pulley does help to retain the factory belt size.

**afraziaaaa** · 09-04-2007, 06:39 PM

Quote:

Originally Posted by cfmfocus2

The water pulley does help to retain the factory belt size.

Got it. So am I correct in stating that the water pump will also be under-driven after I install my UDP?

Also, any idea where I can get these special tools called for in the instructions??? I can't find them anywhere!!!!!

**cfmfocus2** · 09-05-2007, 10:23 AM

Yes. That is correct.

The main tool that is needed is the camshaft alignment tool. It has the bar that goes on the back of the camshafts to hold them in place and the pin that goes on the bottom of the block to make sure it is on TDC. We are looking to offer something like this for the duatec http://focus.c-f-m.com/index.asp?Pag...ROD&ProdID=709. I would check with your local Ford dealership or Mac tools.

**cfmfocus2** · 09-05-2007, 10:38 AM

Quote:

Originally Posted by afraziaaaa

One more question and that's it, I promise!!! (At least until I think of another one

)

What is the "supplied plate" in step 8 of the directions linked in the above post?

"Using the supplied plate, hold the crankshaft pulley in place while removing the crankshaft pulley bolt"

Those instructions are for when using the Ford tools.

**cfmfocus2** · 09-05-2007, 10:40 AM

Quote:

Originally Posted by afraziaaaa

Also, what is the "supplied M6 bolt" referred to in step 7 in the following thread:

http://forums.focaljet.com/5581148-post9.html

???

Part from Ford needed for installation.

**afraziaaaa** · 09-05-2007, 11:53 AM

Quote:

Originally Posted by cfmfocus2

Part from Ford needed for installation.

Oh, so this is the crank pulley bolt that came with my UDP kit?

**afraziaaaa** · 09-05-2007, 11:57 AM

Quote:

Originally Posted by cfmfocus2

Yes. That is correct.

The main tool that is needed is the camshaft alignment tool. It has the bar that goes on the back of the camshafts to hold them in place and the pin that goes on the bottom of the block to make sure it is on TDC. We are looking to offer something like this for the duatec http://focus.c-f-m.com/index.asp?Pag...ROD&ProdID=709. I would check with your local Ford dealership or Mac tools.

My local ford dealer is comprised of morons. They claim that they don't sell tools (which may be true but sounds ridiculous to me) and their service technician asked me "differential...is that the whole transmission..."?

Hahaha...thanks for your help.

**cfmfocus2** · 09-05-2007, 12:15 PM

I will see when we will have our own installation tool available. Very strange that your Ford Dealership could not help. I would think someone at parts should of been able to help you.

**afraziaaaa** · 09-11-2007, 08:00 PM

So any progress on that installation tool? All I need is the pin! I've got the cam alignment bar and access to an impact wrench.

**cfmfocus2** · 09-12-2007, 09:16 PM

We are looking to have the installation tool available next week.

**afraziaaaa** · 09-13-2007, 12:53 AM

Awesome. Will it be posted on your website or will I have to call for it? I think if the proper tools were readily available you guys would sell a lot more of these.

**cfmfocus2** · 09-13-2007, 09:25 AM

Yes. We will have it listed on the website.

**duckmans** · 10-10-2007, 06:26 AM

I could not find the tools on your website. Any updates or a link? Thanks.

**cfmfocus2** · 10-10-2007, 09:41 AM

Quote:

Originally Posted by duckmans

I could not find the tools on your website. Any updates or a link? Thanks.

I was told it should be done on Friday. The installation instructions are being worked on at the moment.

**duckmans** · 10-10-2007, 12:30 PM

Thanks

**afraziaaaa** · 10-17-2007, 12:48 AM

Quote:

Originally Posted by cfmfocus2

I was told it should be done on Friday. The installation instructions are being worked on at the moment.

Sweet. I would like to have a copy of those installation instructions to go with my UDP that has been on my shelf for a few weeks! How can I go about getting a copy once they are ready?

**cfmfocus2** · 10-17-2007, 08:16 AM

Once it is ready. We can e-mail you the instructions.

08-31-2007, 04:18 PM	#1
afraziaaaa TEAM Member Join Date: Jun 2007 Location: Oceanside, CA Posts: 296	Underdrive Pulley - Duratec Can anyone tell me where the larger pulley is supposed to go? (Not the one for the crankshaft.) __________________ Mods: Cosworth CAI & TB, Crane Stg1s, F2 Header, 2.5" exhaust w/high flow and magnaflow straight through, Eibach sport system plus, FS front and rear strut bars, Focus Central STS, Exedy Stage 1, Torsen T2, All 3 motor mounts, Massive fuel rail adapter Soon: cosworth IM, CFM UDP, ZEX wet kit, Crane Stg 2s

08-31-2007, 04:22 PM	#2
cfmfocus2 Premier Sponsor Join Date: Nov 2004 Posts: 847	Re: Underdrive Pulley - Duratec The water pump. __________________ William - Sales Dept / Central Florida Motorsports, Inc. - Since 1996 william@c-f-m.com / Online Customer Service / 407.339.9211 We match ALL advertised prices on products we carry! Our Latest Products / SVT Focus Parts Video of our 12 second Vortech Supercharged 1/4 mile Focus / Engine Specs Come see our new show room!

08-31-2007, 04:22 PM	#3
afraziaaaa TEAM Member Join Date: Jun 2007 Location: Oceanside, CA Posts: 296	Re: Underdrive Pulley - Duratec Also, what is the "supplied M6 bolt" referred to in step 7 in the following thread: http://forums.focaljet.com/5581148-post9.html ??? __________________ Mods: Cosworth CAI & TB, Crane Stg1s, F2 Header, 2.5" exhaust w/high flow and magnaflow straight through, Eibach sport system plus, FS front and rear strut bars, Focus Central STS, Exedy Stage 1, Torsen T2, All 3 motor mounts, Massive fuel rail adapter Soon: cosworth IM, CFM UDP, ZEX wet kit, Crane Stg 2s

08-31-2007, 04:28 PM	#4
afraziaaaa TEAM Member Join Date: Jun 2007 Location: Oceanside, CA Posts: 296	Re: Underdrive Pulley - Duratec One more question and that's it, I promise!!! (At least until I think of another one ) What is the "supplied plate" in step 8 of the directions linked in the above post? "Using the supplied plate, hold the crankshaft pulley in place while removing the crankshaft pulley bolt" __________________ Mods: Cosworth CAI & TB, Crane Stg1s, F2 Header, 2.5" exhaust w/high flow and magnaflow straight through, Eibach sport system plus, FS front and rear strut bars, Focus Central STS, Exedy Stage 1, Torsen T2, All 3 motor mounts, Massive fuel rail adapter Soon: cosworth IM, CFM UDP, ZEX wet kit, Crane Stg 2s

09-04-2007, 12:52 PM	#5
afraziaaaa TEAM Member Join Date: Jun 2007 Location: Oceanside, CA Posts: 296	Re: Underdrive Pulley - Duratec Ok...one more. Does the larger water pump pulley that comes with the kit drive the water pump at normal speed, or is that pulley only used to retain the factory size belt? __________________ Mods: Cosworth CAI & TB, Crane Stg1s, F2 Header, 2.5" exhaust w/high flow and magnaflow straight through, Eibach sport system plus, FS front and rear strut bars, Focus Central STS, Exedy Stage 1, Torsen T2, All 3 motor mounts, Massive fuel rail adapter Soon: cosworth IM, CFM UDP, ZEX wet kit, Crane Stg 2s

09-04-2007, 03:24 PM	#6
only_in_a_domestic Senior TEAM Member Join Date: Mar 2004 Location: Florida Posts: 1,474	Re: Underdrive Pulley - Duratec both im pretty sure __________________ weight reduction= no sig:-)

09-05-2007, 10:23 AM	#9
cfmfocus2 Premier Sponsor Join Date: Nov 2004 Posts: 847	Re: Underdrive Pulley - Duratec Yes. That is correct. The main tool that is needed is the camshaft alignment tool. It has the bar that goes on the back of the camshafts to hold them in place and the pin that goes on the bottom of the block to make sure it is on TDC. We are looking to offer something like this for the duatec http://focus.c-f-m.com/index.asp?Pag...ROD&ProdID=709. I would check with your local Ford dealership or Mac tools. __________________ William - Sales Dept / Central Florida Motorsports, Inc. - Since 1996 william@c-f-m.com / Online Customer Service / 407.339.9211 We match ALL advertised prices on products we carry! Our Latest Products / SVT Focus Parts Video of our 12 second Vortech Supercharged 1/4 mile Focus / Engine Specs Come see our new show room!

09-05-2007, 12:15 PM	#14
cfmfocus2 Premier Sponsor Join Date: Nov 2004 Posts: 847	Re: Underdrive Pulley - Duratec I will see when we will have our own installation tool available. Very strange that your Ford Dealership could not help. I would think someone at parts should of been able to help you. __________________ William - Sales Dept / Central Florida Motorsports, Inc. - Since 1996 william@c-f-m.com / Online Customer Service / 407.339.9211 We match ALL advertised prices on products we carry! Our Latest Products / SVT Focus Parts Video of our 12 second Vortech Supercharged 1/4 mile Focus / Engine Specs Come see our new show room! Last edited by cfmfocus2 : 09-05-2007 at 12:36 PM.

09-11-2007, 08:00 PM	#15
afraziaaaa TEAM Member Join Date: Jun 2007 Location: Oceanside, CA Posts: 296	Re: Underdrive Pulley - Duratec So any progress on that installation tool? All I need is the pin! I've got the cam alignment bar and access to an impact wrench. __________________ Mods: Cosworth CAI & TB, Crane Stg1s, F2 Header, 2.5" exhaust w/high flow and magnaflow straight through, Eibach sport system plus, FS front and rear strut bars, Focus Central STS, Exedy Stage 1, Torsen T2, All 3 motor mounts, Massive fuel rail adapter Soon: cosworth IM, CFM UDP, ZEX wet kit, Crane Stg 2s

09-12-2007, 09:16 PM	#16
cfmfocus2 Premier Sponsor Join Date: Nov 2004 Posts: 847	Re: Underdrive Pulley - Duratec We are looking to have the installation tool available next week. __________________ William - Sales Dept / Central Florida Motorsports, Inc. - Since 1996 william@c-f-m.com / Online Customer Service / 407.339.9211 We match ALL advertised prices on products we carry! Our Latest Products / SVT Focus Parts Video of our 12 second Vortech Supercharged 1/4 mile Focus / Engine Specs Come see our new show room!

09-13-2007, 12:53 AM	#17
afraziaaaa TEAM Member Join Date: Jun 2007 Location: Oceanside, CA Posts: 296	Re: Underdrive Pulley - Duratec Awesome. Will it be posted on your website or will I have to call for it? I think if the proper tools were readily available you guys would sell a lot more of these. __________________ Mods: Cosworth CAI & TB, Crane Stg1s, F2 Header, 2.5" exhaust w/high flow and magnaflow straight through, Eibach sport system plus, FS front and rear strut bars, Focus Central STS, Exedy Stage 1, Torsen T2, All 3 motor mounts, Massive fuel rail adapter Soon: cosworth IM, CFM UDP, ZEX wet kit, Crane Stg 2s

09-13-2007, 09:25 AM	#18
cfmfocus2 Premier Sponsor Join Date: Nov 2004 Posts: 847	Re: Underdrive Pulley - Duratec Yes. We will have it listed on the website. __________________ William - Sales Dept / Central Florida Motorsports, Inc. - Since 1996 william@c-f-m.com / Online Customer Service / 407.339.9211 We match ALL advertised prices on products we carry! Our Latest Products / SVT Focus Parts Video of our 12 second Vortech Supercharged 1/4 mile Focus / Engine Specs Come see our new show room!

10-10-2007, 06:26 AM	#19
duckmans TEAM Member Join Date: Aug 2006 Location: Florida Posts: 308	Re: Underdrive Pulley - Duratec I could not find the tools on your website. Any updates or a link? Thanks.

10-10-2007, 12:30 PM	#21
duckmans TEAM Member Join Date: Aug 2006 Location: Florida Posts: 308	Re: Underdrive Pulley - Duratec Thanks

10-17-2007, 08:16 AM	#23
cfmfocus2 Premier Sponsor Join Date: Nov 2004 Posts: 847	Re: Underdrive Pulley - Duratec Once it is ready. We can e-mail you the instructions. __________________ William - Sales Dept / Central Florida Motorsports, Inc. - Since 1996 william@c-f-m.com / Online Customer Service / 407.339.9211 We match ALL advertised prices on products we carry! Our Latest Products / SVT Focus Parts Video of our 12 second Vortech Supercharged 1/4 mile Focus / Engine Specs Come see our new show room!