ALL DTC for ford - Page 2 - The Ford Focus Forum

**fiends911** · 05-02-2006, 07:16 AM

throwing P0147 anyone know what that is? its off a duratec and some of the codes are differnet. i'm pretty sure its a fuel or o2 sensor thing but i wanna be sure.

**Z63R** · 05-06-2006, 07:14 PM

Todd's sis-in-law-to-be's Focus automatic has thrown a P0732... ?

**j20000** · 05-07-2006, 06:26 PM

Quote:

Originally Posted by Z63R

Todd's sis-in-law-to-be's Focus automatic has thrown a P0732... ?

Thats a wierd one....
P0732 Gear 2 Incorrect Ratio

**j20000** · 05-07-2006, 06:27 PM

Quote:

Originally Posted by fiends911

throwing P0147 anyone know what that is? its off a duratec and some of the codes are differnet. i'm pretty sure its a fuel or o2 sensor thing but i wanna be sure.

P0147 Heated O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 3)

**j20000** · 05-07-2006, 06:31 PM

Here are all of the DTC's. Its just a list of them, not an explination like on here...but its just a list of ALL of the OBDII codes.

OBDII CODES <----- Click Here

**BUR_ZX3** · 05-09-2006, 06:18 PM

Quote:

Originally Posted by j20000

Thats a wierd one....
P0732 Gear 2 Incorrect Ratio

I knew that.... but what does it MEAN?

**j20000** · 05-10-2006, 03:21 PM

it means Gear 2...incorrect ratio.

I dunno what the heck that could mean...its not like the wrong gears could just find their way into the car...which makes me think.... why would Ford even have a DTC for that?

thats just a really wierd one.

**Z63R** · 05-16-2006, 05:32 PM

It means that the PCM is sensing incorrect revs for 2nd gear which may mean slipping friction materials (prolly), or a bad torque convertor (not likely)...

Incorrect revs for 2nd geear relative to all four speeds; in other words, change the tire size with a healthy trans, it won't notice. Go with a big change in tire size and the PCM's revs-per-mile should be reprogrammed only for correct speedo readings.

**JDB2001** · 05-22-2006, 05:17 PM

2001 ZX3. Had jerky engine at ~ 40mph & code 0401. Dealer replaced DPFT - fixed jerkiness but now engine takes 15 seconds to drop to idle (if it gets there at all). Then had code 1506 Dealer replaced IAC. No change but I'm a lot lighter in the wallet. Any ideas?

**wife_hates_car** · 05-24-2006, 04:03 PM

Two ford dealers have been unable to read my computer. My 2.3 PZEV runs fine, but my check engine light comes on. The local dealer is able to clear the light, but it reappears in a few miles. What could I cause my computer to not be reading at two different dealers? Any help?

**all2envyZx3** · 08-30-2006, 07:36 PM

My friends 2.3 auto displayed d900?
anyone know what that one is?

Thanks in advance

**Zona Kona** · 09-04-2006, 02:38 PM

These are for all Ford's right not just Focus?

the Dirt Brown Kona in Arizona

All cars in general OBD II brought generic codes to the public... so a Pontiac can have the same failure code as a Ford.

**ClintB1321** · 10-08-2006, 04:14 PM

what should i do about a P0191 DTC?

**Maddogmil** · 12-01-2006, 03:11 PM

HOW BOUT THE INFO ON CAUSES OF P2196 PLEASE! rumor has it that o2 dont fail rich.

**OmniFocus** · 12-01-2006, 04:20 PM

Quote:

Originally Posted by RickB1321

what should i do about a P0191 DTC?

That would be either a tuning issue, a pump issue, or a sensor/wiring issue.

**OmniFocus** · 12-01-2006, 04:25 PM

Quote:

Originally Posted by Maddogmil

HOW BOUT THE INFO ON CAUSES OF P2196 PLEASE! rumor has it that o2 dont fail rich.

I'd recommend starting a fresh thread, this is informational only.

In your case, I'd examine wiring to/from the O2 sensor to verify it isn't in some way damaged. Once that is verified good, you have to assume that either the sensor is non-functional, or it is actually reading rich due to a tuning or mixture problem elsewhere.

I'd recommend working with somebody experienced to examine the car.

**florintopa** · 02-22-2007, 10:06 PM

Hi,
I have recently had a P0460 code on my 2002 Focus. I found on the net that could be caused by an aftermarket remote starter .I have a remote starter installed for about 3 years which worked well untill recently when it began to make some problems.Could be that the cause?What else should I check?Otherwise, the car is running well.
Thanks !

**ColtonnotloC** · 03-09-2007, 11:48 PM

Wow this thread is helpful haha, but when I set it up to the computer it came back with PO602 an 605. Any suggestions to fix this? The check engine light was on, but after I took out the performance chip it was off again but I drove probably another 100 miles and its now back on. My car's power seems really low also and kinda stutters or hesitates during high rpm's.

Thx for the help guys

**eggyolk04zx3** · 08-04-2007, 01:43 AM

what about p2195? i got this along with p0171.

**belsvtr** · 10-09-2008, 03:27 PM

what does pcm mean?
and besides that you guys seem to know your sensors, well i have a problem with my svt. i was driving it normal and out of no where the engine just bogged on me, i figured it was the timing belt, so i get it towed home took off my timing cover and valve cover, and my belt is good no cracks no missing teeth nothing, it skipped timing, how? i dont know. obviously it bent my exhaust valves so i changed them out. ok everything seems good i go ahead and crank it up, and there is some weird knocking noise comming from the engine at idle, ok i give it a lil gas it gets worse and then it fades away. i dont want to drive it with this problem. can someone please help me diagnose this problem, i love my svt and i want to still drive it!!

**Armanduhx3** · 09-03-2009, 04:28 PM

thanks!

**1svt4u2c** · 09-09-2009, 02:33 AM

I found a good website for some other codes not listed. I just got the B1600 and B1602 for the PATS system. Fun stuff! Oh well, here's the link.

http://www.svtlightnings.com/scantoo...tc%20codes.htm

**Lancer211** · 11-10-2009, 08:07 PM

This is certainly NOT all DTC for Ford, because just today I got a P2195....

05-02-2006, 07:16 AM	#26 (permalink)
fiends911 TEAM Member Join Date: Aug 2002 Location: northern, NJ Posts: 910	Re: ALL DTC for ford throwing P0147 anyone know what that is? its off a duratec and some of the codes are differnet. i'm pretty sure its a fuel or o2 sensor thing but i wanna be sure. __________________ Member Strictly Focused North Jersey www.strictlyfocused.com, http://www.myspace.com/strictlyfocused, http://www.myspace.com/fiends911 "I'm ready. It doesn't matter with who or where. On foot or on horseback. With maces or poleaxes. To fight. To first blood or to death. It doesn't matter, I'm ready to fight." -- Aleksander Emelianenko

05-06-2006, 07:14 PM	#27 (permalink)
Z63R Official [FJ] Distinguished Advisor Join Date: May 2004 Location: El Lay Ca Posts: 22,829	Re: ALL DTC for ford Todd's sis-in-law-to-be's Focus automatic has thrown a P0732... ? __________________ . "I replaced the battery cables to the starter. I've been dreading it since the PowerWorks severely restricts access to the starter... A good job for a 6'2" 150lb pianist, but not so hot for a 5'10" 220lb wookie. - OmniFocus 2.3 Duratec ZX3 + some bits

05-16-2006, 05:32 PM	#33 (permalink)
Z63R Official [FJ] Distinguished Advisor Join Date: May 2004 Location: El Lay Ca Posts: 22,829	Re: ALL DTC for ford It means that the PCM is sensing incorrect revs for 2nd gear which may mean slipping friction materials (prolly), or a bad torque convertor (not likely)... Incorrect revs for 2nd geear relative to all four speeds; in other words, change the tire size with a healthy trans, it won't notice. Go with a big change in tire size and the PCM's revs-per-mile should be reprogrammed only for correct speedo readings. __________________ . "I replaced the battery cables to the starter. I've been dreading it since the PowerWorks severely restricts access to the starter... A good job for a 6'2" 150lb pianist, but not so hot for a 5'10" 220lb wookie. - OmniFocus 2.3 Duratec ZX3 + some bits

05-22-2006, 05:17 PM	#34 (permalink)
JDB2001 Newbie Join Date: May 2006 Posts: 3	Re: ALL DTC for ford 2001 ZX3. Had jerky engine at ~ 40mph & code 0401. Dealer replaced DPFT - fixed jerkiness but now engine takes 15 seconds to drop to idle (if it gets there at all). Then had code 1506 Dealer replaced IAC. No change but I'm a lot lighter in the wallet. Any ideas?

05-24-2006, 04:03 PM	#35 (permalink)
wife_hates_car Rookie Join Date: Jul 2005 Location: NW Posts: 14	Re: Not communicating? Two ford dealers have been unable to read my computer. My 2.3 PZEV runs fine, but my check engine light comes on. The local dealer is able to clear the light, but it reappears in a few miles. What could I cause my computer to not be reading at two different dealers? Any help? __________________ 2004 2.3PZEV, MMS Stage 1 cams, CAI, BS delete, Borla exhaust, SCT tuning, SVT suspension- Thanks Walter

08-30-2006, 07:36 PM	#36 (permalink)
all2envyZx3 Senior TEAM Member Join Date: Aug 2002 Location: Grand Junction,CO Posts: 2,288	Re: ALL DTC for ford My friends 2.3 auto displayed d900? anyone know what that one is? Thanks in advance

09-04-2006, 02:38 PM	#37 (permalink)
Zona Kona Moderator Join Date: Sep 2002 Location: Zona Posts: 12,927	Re: ALL DTC for ford These are for all Ford's right not just Focus? the Dirt Brown Kona in Arizona All cars in general OBD II brought generic codes to the public... so a Pontiac can have the same failure code as a Ford. __________________ For Sale: Power Steering Line, EGR Tube, Pedals, Wiper Switch, Oil Pump, Speakers, AC/Vent/Defroster Buttons, Front Struts & Rear Shocks, Turn Signal Switch Last edited by OmniFocus; 12-01-2006 at 04:19 PM.

10-08-2006, 04:14 PM	#38 (permalink)
ClintB1321 [FJ] Specialist Join Date: Apr 2006 Location: Culver City, CA Posts: 5,364	Re: ALL DTC for ford what should i do about a P0191 DTC? __________________ Boost Camel Racing...when you don't care how rice you look in the name of speed :)

12-01-2006, 03:11 PM	#39 (permalink)
Maddogmil Rookie Join Date: Sep 2003 Location: Buffalo, NY USA Posts: 47	Re: ALL DTC for ford HOW BOUT THE INFO ON CAUSES OF P2196 PLEASE! rumor has it that o2 dont fail rich. __________________ Centennial edition (2003 ZTS Sedan) 2.3L PZEV FocusSport Cool-Flo race intake system

02-22-2007, 10:06 PM	#42 (permalink)
florintopa Newbie Join Date: Feb 2007 Posts: 3	Re: ALL DTC for ford Hi, I have recently had a P0460 code on my 2002 Focus. I found on the net that could be caused by an aftermarket remote starter .I have a remote starter installed for about 3 years which worked well untill recently when it began to make some problems.Could be that the cause?What else should I check?Otherwise, the car is running well. Thanks !

03-09-2007, 11:48 PM	#43 (permalink)
ColtonnotloC Junior Member Join Date: Mar 2007 Location: Everett, WA Posts: 97	Re: ALL DTC for ford Wow this thread is helpful haha, but when I set it up to the computer it came back with PO602 an 605. Any suggestions to fix this? The check engine light was on, but after I took out the performance chip it was off again but I drove probably another 100 miles and its now back on. My car's power seems really low also and kinda stutters or hesitates during high rpm's. Thx for the help guys

08-04-2007, 01:43 AM	#44 (permalink)
eggyolk04zx3 TEAM Member Join Date: Mar 2007 Location: Newport, TN Posts: 200	Re: ALL DTC for ford what about p2195? i got this along with p0171. __________________ FS vibrant 2 3/8 catback exhaust for hatchback $200obo FS AEM polished short ram intake zetec w/ maf $150obo pm me with any questions.. pics in FS threads

10-09-2008, 03:27 PM	#45 (permalink)
belsvtr Rookie Join Date: Oct 2008 Posts: 6	Re: ALL DTC for ford what does pcm mean? and besides that you guys seem to know your sensors, well i have a problem with my svt. i was driving it normal and out of no where the engine just bogged on me, i figured it was the timing belt, so i get it towed home took off my timing cover and valve cover, and my belt is good no cracks no missing teeth nothing, it skipped timing, how? i dont know. obviously it bent my exhaust valves so i changed them out. ok everything seems good i go ahead and crank it up, and there is some weird knocking noise comming from the engine at idle, ok i give it a lil gas it gets worse and then it fades away. i dont want to drive it with this problem. can someone please help me diagnose this problem, i love my svt and i want to still drive it!!

09-03-2009, 04:28 PM	#46 (permalink)
Armanduhx3 "Shut Up man, get on my horse" Join Date: Apr 2009 Location: Jacksonville, Florida Posts: 1,691	Re: ALL DTC for ford thanks! __________________ aRmanda\|\|Tweet\|\|Building teh zx3\|\|Girls of FJ

09-09-2009, 02:33 AM	#47 (permalink)
1svt4u2c Senior TEAM Member Join Date: Jun 2004 Location: York, PA Posts: 2,840	Re: ALL DTC for ford I found a good website for some other codes not listed. I just got the B1600 and B1602 for the PATS system. Fun stuff! Oh well, here's the link. http://www.svtlightnings.com/scantoo...tc%20codes.htm __________________ .._____ ............<--2003 SVT Focus /___l__\__ ........#2940 of 3985 l(o)____(o)l........Build Date 06/13/03

11-10-2009, 08:07 PM	#48 (permalink)
Lancer211 Senior TEAM Member Join Date: Mar 2009 Location: Tucson, AZ Posts: 2,330	Re: ALL DTC for ford This is certainly NOT all DTC for Ford, because just today I got a P2195.... __________________ For sale: Eibach Pro-Kit springs, sedan taillight, lower grille, DPFE, EVR, MAFS, side markers, trunk handle, fuel door, gas pedal, headlight switch, AC/vent/defrost button, hazard switch, ashtray, silver console bezel, HVAC controls. 2004 infrared Focus SE Zetec ATX sedan "Ruby" CarDomain Page

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode